Guide :Home : Dartmouth 2pc. E/F Toilet CST754SF-01

Toto Dartmouth toilet flapper/chain design flaw

I have a toto toilet. The flapper/chain and handle rod layout is such that the flapper is pulled sideways when the toilet is flushed, not pulled straight up, but sideways. That is the design. The problem; the flapper must return itself and square up on the hole to properly seal. Sometimes it works, sometimes it doesn't and the toilet runs. The flapper is perfect, not worn. The toilet has done this since new. If I didn't bend the rod to somewhat lessen the sideways pull, it would be worse. Design problem, bad layout. A new replacement rod with an offset would fix it. Any available? W

Research, Knowledge and Information :

Toto Dartmouth - Flapper Replacement Problems | Terry Love ...

Toto Dartmouth Design Flaw Flapper Valve. Chain Pull I have a Dartmouth and the design is flawed, when the handle pulls the flapper valve it does not go straight up ...
Read More At :

chronic toilet clog -

... a styrofoam float on the flapper chain, bring it closer to the flapper for a ... TOTO is you want to ... a design flaw with a particular kohler toilet?
Read More At :

Champion 1.6 GPF Elongated One-Piece Toilet -

... a classic design. The low consumption toilet features ... Toto Dartmouth 1.6 GPF Toilet ... traditional flapper. The American Standard toilet is eco ...
Read More At :

American Standard Optum Vormax Toilet Review - Toilet Found!

Don't buy this American Standard Optum Vormax Toilet before you ... As each flapper has a float attached via a chain, ... The design flaws is probably the main ...
Read More At :

15 Toilet Tune Ups | Ask the Builder

The chain that connects between the flapper valve and the flush handle may be too ... These toilets have basic design flaws. ... 3 Responses to 15 Toilet Tune Ups.
Read More At :

Danco Toilet Repair Kit - charmin-toilet-paper-30-jumbo-rolls ...

Danco Toilet Repair Kit, widest range of toilet suites, bathrooms and bidets.
Read More At :

Suggested Questions And Answer :

Toto Dartmouth toilet flapper/chain design flaw

Your right this is a poor design. Space was the main reason for this and functionality was sacrificed. However, you can get a replacement rod at a major plumbing store. You could rig it by attaching a stem to the valve assembly. Allow the chain or rubber piece to slide over it. It is kind of like putting a permanent finger in the path of the chain to give it a "direct" lift up. This would then force the chain to go up instead of at an angle.
Read More At : Dartmouth 2pc. E/F Toilet CST754SF-01...

Toto flush handle problem

Did you try a new flapper? sometimes those are the reason they wont flush properly. check out the american standard cadet 3 it's half as much as a toto and works just as well
Read More At : Dartmouth 2pc. E/F Toilet CST754SF-01...

Flush problem with toto toilet

If your hooked to city water it can be cause of the high water pressure comes across and keeps flapper from seating rite. Take a empty plastic bottle,cut it in half long ways. flush toilet then place plastic bottle between fill valve and flapper,trying to devert water away from where flapper seats. good luck.
Read More At : Dartmouth 2pc. E/F Toilet CST754SF-01...

Toto Toilet - no water flow to refill tank after flush

Remove the tank lid and look at the fill valve. Is it a yellow valve? This fill valve is common on the Toto Toilets and can easliy plug with debrie. They can be disassmbled and cleaned. however, I usually just replace the valve with Fluid Master Fill valve. You will also want to check the water coming into the toilet by turning off the water that supplies the toilet and disconnecting the water supply line. After removing the water supply line turn on the water at the valve to make sure that the water is flowing properly. Check the supply line also to make sure it is not plugged. Be sure and place a small container to catch the water that will come from the valve. A towell will also help from making too much of a mess. If the Supply line and the valve are clear the problem is in the fill valve. The G-Max system denotes the Flushiing system which is a 3" flapper that allows the water from the tank to flow into the bowl quicker. Good Toilets! sanray
Read More At : Toilets ST753S 01 Cotton Dartmouth Toilet with Traditional......

Toto toilet, flapper doesn't stay up long enough to flush

One of two things is the problem. First, make sure that you have a tight chain with little slack. If there's too much slack, the flapper won't catch in the passing air to stay up. Second, the flapper is not correct for that style of toilet. You might want to look into purchasing a new Kolby filter that has a removeable cone in the center. Move that cone to 12 o'clock to allow the maximum amount of water to run through the flush valve. If the flapper you have now is flat, it needs to have a cone in the center on the underside.
Read More At : Toilets ST753S 01 Cotton Dartmouth Toilet with Traditional......

Not enough water in the bowl

The fill valve probably has a float that surrounds the pole that extends from the bottom of the tank. The float usually has a metal rod that comes down with a clip to adjust the float. Move that clip up so that the float sits higher-this should add more water to the tank.
Read More At : Toilets ST753S 01 Cotton Dartmouth Toilet with Traditional......

The toilet tank will not tighten done to the three points of contact. I have set the tank extremely leaning forward begin to tighten and the tank pulls straight up. this is second toilet this is happening with. i am very familiar with the Toto drakes. Installed three in previous house without this problem.

Take the tank back off and make sure the tank to bowl gasket is set correctly and the make sure you tighten the bolts down evenly.
Read More At : Drake 2pc. E/F Toilet ADA CST744SL-01...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0957 seconds