Jacuzzi not so cuzzi. Could it be just the heater?
There are usually two breakers for a hot tub. One sends power to the heater and another sends power to the big pump.
Be sure both breakers are turned all the way too off and then turn them to on. Next look for a reset button on inside of the jacuzzi which may have to be reset.
good luck Read More At : Home...
Can not get the jets to work
Most of the control buttons on a tub are not electrical. These buttons are connected to an air line that runs to the motor. Sometimes an aggressive button push can literally blow the air line right off of the bottom of the button.This problem is as easy to fix as it sounds. Find the loose air line and push it back onto the button. You will need to open up your access panel. Bring a flashlight.Be sure to check the connection at the motor too. Good luck Read More At : Home...
I have a whirlpool bath in my master bath in my mobile home, years ago my grandson pushed the button to activate the jets without water in the tub, it hasn't worked since, yesterday I had a friend who is an electrician check it out, there is power running to the plug in for the motor and power in the motor as well, I filled the tub above the jets, pushed the button, and nothing, it's been like this for years, and I really want it to work, there are two clear hoses that say air switch, they are two separate hoses, connected on one end, but not the other, is that the way they should be or are they supposed to be connected to something on each end. I'm very frustrated with this issue and will gladly take any help you can offer.
The air switch should be connected to a switch by the motor the air switch is ur on off and should run from the button to another switch by motor the air switches were put in so there was not live wiring by the tub surface ,the the tub button/switch is like a bellows and pushes air into tube to turn switch on/off Read More At : Kohler...
My bathtub drain leaks. Is there a product to
No, not without sealing, I mean clogging, the drain. Do you know exactly where the leak is coming from? I would suspect that the water is getting around the drain, instead of down the drain. The visible part of the drain should unscrew from the part that is underneath. That bottom part is likely permanently sealed to your drain plumbing.
You may be able to easily fix your leak by:
#1 Unscrewing the visible drain top.
#2 Replacing the washer under that top. This will seal your tub to your drain. All water will then be forced to flow down the drain properly.
#3 Screw the top of your drain back into place WITHOUT folding or wrinkling the new washer.
Good luck Read More At : 1221-H-0 Seadream 6' Whirlpool Bath Tub with Heater...
I BOUGHT A FORCLOSED HOME AND IT HAS A CORNER STYLE WHIRLPOOL BATH- SINCE I DONT KNOW A THING ABT THESE CREATURES I HAVE 2 QUESTIONS.
I HAVE A DRIP STYLE LEAK FROM AN ITEM THAT ON THE INSIDE OF THE TUB IS LIKE A CAP ABT THE SIZE OF A QUARTER, 1/8' THICK. THIS CAP TURNS -I NOTICED IF I TURN IT ALL THE WAY COUNTER CLOCKWISE THE DRIP STOPS. WHAT IS IT AND WHAT DOES IT DO? THE UNDERSIDE HAS A BLUE CLEAR LINE GOING TO A JET.
# 2 THE INLINE HEATER DOESNT SEEM TO KEEP THE WATER AS WARM AS IT SHOULD- IS THERE ANYWAY TO ADJUST THE TEMP? THANKS..HOME DEPOT ISNT VERY HELPFUL
p.s. where do I find the model number of this tub?
Inline heaters for whirlpool bathtubs will not and cannot maintain any comfortable water temperature. Their sole function is to slow the time it takes for the water to cool off. The myth of their capabilities has long been a misleading sales propaganda joke in the industry.
Not all manufacturers put their model numbers on their tubs. Those that do will almost always post it on a label in the area of the tub where the back usually rests in the region of the motor but not on the motor itself.
I believe your quarter size cap is an air control for you jet. It controls the amount of air coming out the jet when the tub is full of water and the motor is on. You should see the difference in swirling water turning it from right to left or the other way around. If yours has a leak then I certainly hope you find the Model number. Good luck. Read More At : American Standard...
How to Change White Water Whirlpool Tub Jet Hardware
I recommend that you consider spray painting the gold hardware with brushed nickel rusteoleum paint. IF you decide to go this route you must lightly abrade the gold surface with emery cloth then prime with rusteoleum primer, let that dry and the final coat will be the brushed nickel. I have done this and it turned out excellent. I get compliments on it.
Regarding your other issues, you will be happiest with white water parts. That being said, it is likely that locally procured parts might fit. I would get one set of parts and try them.
You will likely find the model number etc. on a plate in the mechanical compartment of the spa. Read More At : 1107-R-0 ProFlex Bath Tub with Flange and Right Hand Drain......
Bathtub jets will not start
Our reset for the jets were hidden in the master closet behind the tub. We also found another access point to the tubs inner workings in the same place. Also, make sure they open all the air intakes and the tub is filled prior to testing. On ours if water is not above a certain level it won't come on. Read More At : Home...