Guide :Home : Home

I have a whirlpool washing machine and I need to check the filter, please can you tell me where it is. It is a AWO/D 4505 model Thanks

Posted by evans_cp on Jan 15, 2009

Research, Knowledge and Information :


how do i clean pump on whirlpool AWO/D 4505? - how to mend it ...


tHE RED LIGHT HAS COME ON ON MY WHIRLPOOL AWO/D 4505 WASHING MACHINE TELLING ME ... do i need to do please ... model number RSG964J . We checked the filter ...
Read More At : howtomendit.com...

Whirlpool AWO/D & AWD Series Washing Machine Error Fault Codes


... part for your washing machine, you will need the full model ... Whirlpool AWO/D & AWD Series Washing Machine ... can tell me what is wrong with my Whirlpool ...
Read More At : www.how-to-repair.com...

HI, I have a Whirlpool AWO/D 4505. Recently it has continued


... I have a Whirlpool AWO/D 4505. Recently it has continued ... Can you tell me if there is an auto ... inside of the washing machine and therefore have no ...
Read More At : www.justanswer.com...

UK Whitegoods • View topic - AWO/D 4305 whirlpool washer, red ...


AWO/D 4305 whirlpool washer, ... Please if anyone can help me to determine what ... If your washing machine will not drain the cause will normally be that either ...
Read More At : www.ukwhitegoods.co.uk...

Whirlpool Awo/d 4505 manual for clean pump please?


... whirlpool awod 4505 manual clean pump please. ... Awo/d 4505 manual for clean pump please? ... AQ9D69I washing machine. As far as I can tell I need to ...
Read More At : howtomendit.com...

My Whirlpool AWO/D 6707 washing machine stops continuously


My Whirlpool AWO/D 6707 washing machine stops continuously throughout the ... What you need to do is meter ... Lamona HJA6110 Please can you tell me how to get ...
Read More At : www.justanswer.com...

Suggested Questions And Answer :


I have a whirlpool washing machine and I need to check the filter, please can you tell me where it is. It is a AWO/D 4505 model Thanks


Your filter/screens are where your washer hot and cold hoses connect to you washer. You will have to turn the water off on your washer, and unscrew the hoses at the washer. You will see them at the end of the hose or in the washer itself. Take them out and clean them.
Read More At : Home...

How to Change White Water Whirlpool Tub Jet Hardware


I recommend that you consider spray painting the gold hardware with brushed nickel rusteoleum paint. IF you decide to go this route you must lightly abrade the gold surface with emery cloth then prime with rusteoleum primer, let that dry and the final coat will be the brushed nickel. I have done this and it turned out excellent. I get compliments on it. Regarding your other issues, you will be happiest with white water parts. That being said, it is likely that locally procured parts might fit. I would get one set of parts and try them. You will likely find the model number etc. on a plate in the mechanical compartment of the spa.
Read More At : 1107-R-0 ProFlex Bath Tub with Flange and Right Hand Drain......

How to identify make and model of old whirlpool tub?


This is a problem common to all whirlpool/air jet style tubs. The pumps become air locked due to the water evaporating from lack of use. All tubs need, and have, SOME means of priming the pump, this is most likely what the problem was, originally, for you. This time in particular you found it to be electrical in nature but for future reference, for you and all who have these style of tubs, I am putting this out there. Some where on the tub, usually along the top edge of the tub is a vent knob that controls the amount of air that the pump is allowed to mix with the water for the jets, usually by closing this valve all the way (tub needs to be full of water of course) and running the pump for a minute or 2, you should be able to get the pump pumping water again, if not you may need to do something else with your particular set-up to get it purged of air, the pumps in jacuzzi tubs are designed to pump water, not air, so if the motor is running but you get no jet action, your most likely air locked and need to prime pump/purge air.
Read More At : Home...

American Standard whirlpool model 2425 how much stuctolite 50 lb?


Some people use spray foam which you can add later
Read More At : Evolution 2425V-LHO.020 White 5 Feet x...

I have lost the cleaning instructions for my new Plebe 5' whirlpool. Could you please tell me what to use to clean it with? I remember seeing cleaning instructions; please tell me what not to use to clean it with also. Thanks,


I just use Vinagure in warm water and let it run due to some cleaning products will break down the sealing compound on the piping and then you have trouble........Vinagure is safe and environment friendly as well it is not harmful to your skin........Hope this helps.
Read More At : Home...

Can't adjust flush time for complete flush, low bowl water level


Flush time depends on how much water is in it, the water level flote has an adjuster on it, but i cant rember were it is,,, sorry
Read More At : K-11470-0 White Wellworth Complete Solution round-front......

I purchased a HamptonBay bathroom Bar Light that has 4 lights going across I purchase this product from HomeDepot a few years ago before 2009 Home Depot has one that is a little like the one I have but it has 3 lights going across I need help to with replacing the lights not sure how to take the light cover off to replace the light the model number that was given to me from home depot was 136654 price 109.00 with UPC Code 18212-057391, If someone can please look into this for me and let me know how to take the Glass cover off. Thank you very much.


Check to see if the chrome rings that cover the base of the bulbs unscrews , if they don't then check for small screws around the edges of the light , Last see if there is a decorative knob on the face of the light . those wold usually be the only ways to remove the cover, Most likely the first option.
Read More At : Hampton Bay...

I have a jacuzzi whirlpool tub in my home that has started to leak at the three button control panel. Flooded out the bathroom so I cut a hole in the tile surround and when the pump is running it leak


First thing you need to do is remove some skirting so you can actually see where the water is coming from. The 3 position control panel would only leak if the water was above it or covering it if it is located in the wall of the tub. That solution would only require the bather to NOT fill the tub quite so full. IF however the water is coming from another location then that will be noticeable when you are checking for the water leak.
Read More At : Jacuzzi...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || diydecoridea.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1004 seconds