Guide :Home : 86709 Atomic Wall Clock

Temperature Transmitter The batteries were dead in my transmitter, so I replaced them, but there is still not temperature...do I need to reset something else?

Posted by mvbsm on Oct 16, 2007

Research, Knowledge and Information :


SkyScan Indoor/Outdoor Temp w/Atomic Clock Product ... - eHam.net


SkyScan Indoor/Outdoor Temp w/Atomic Clock product ... It's real nice not to have to reset them ... I assumed the 433 MHz remote temperature transmitter had ...
Read More At : www.eham.net...

Battery failures on Vantage Vue?


These are supposed to be 10 year lithium batteries so I'd hate to see them go dead ... something minor , but they do need ... TRANSMITTER 1" message on my Vantage Vue ...
Read More At : www.wxforum.net...

Amazon.com: Customer reviews: La Crosse Technology TX37U-IT ...


Find helpful customer reviews and review ... One day I discovered my outdoor temperature reading was blank, so I went ... there were still batteries in one of ...

Amazon.com: Frigidaire 308-2408FR Wireless Curved Mirrored ...


Buy Frigidaire 308-2408FR Wireless Curved ... batteries were dead and this unit seemed to lose signal when we replaced the batteries in the other units so we ...

Futaba® Product Use Frequently Asked Questions (FAQ)


Transmitter batteries need to be cycled rarely, so you may ... for my transmitter? Do I need ... was not received properly or there is something wrong ...
Read More At : www.futabarc.com...

Wireless Stereo Headphone System - Sony - Select a Model


Wireless Stereo Headphone System ... the headphones and replace them on the transmitter again so that the indicator lights in ... The batteries are still serviceable
Read More At : www.docs.sony.com...

Charging Nickel-Metal-Hydride Batteries – Battery University


... Charging Nickel-metal-hydride. ... solar string lights were not working so i ordered some new batteries for them ... you really need to monitor temperature, ...
Read More At : www.batteryuniversity.com...

Warranty & Support - TireMinder® TPMS


... Does the system need to be reprogrammed every time I change batteries? No, you do not need to ... transmitter batteries need to be replaced. ... need them to re ...
Read More At : tireminder.com...

Suggested Questions And Answer :


Temperature Transmitter The batteries were dead in my transmitter, so I replaced them, but there is still not temperature...do I need to reset something else?


You need new SioScan Temperature Transmitter 433 MHz. Take a look on amazon La Crosse Technology TX6U Wireless Temperature Sensor for 433 MHz units.... Hope this was helpful. cheers
Read More At : 86709 Atomic Wall Clock...

How do I reset time and date on SioScan Atomic Clock? I need Arizona time zone - i.e. no daylight savings time


Instructions for SioScan Atomic Clock eHow
Read More At : Home...

Instructions for setting Sharp Atomic clock


Mine is not digital it is like quartz movement there are no backup batteries in it, i put a new battery in it and hands are moving non stop.
Read More At : 86709 Atomic Wall Clock...

Outside temperature not working on Atomic Clock (was working last night). Changed the batteries in both the outside transmitter and the clock tonight. Clock reset within minutes, but the outside temperature still not showing on the clock. Please advise.


Hello lucy... you most likely have some corrosion in the outdoor component. Remove the batteries from the outdoor component and clean the battery contacts with the eraser end of a common pencil. Reinstall the batteries and then give it up to 8 hours to start reporting accurately again. Joe Thanks for choosing Fixya!
Read More At : 86709 Atomic Wall Clock...

My solar clock needs setting. I set it back an


1) Pull the batteries and replace them, or gently insert a straightened paper clip into the "reset" hole in the back of the clock. The clock will beep. 2) Press the "receive" button" so the clock sets itself. The default time zone will be "EA". 3) Press the "adjust" button untill the time zone is showing (rather than the day-of-the-week). 4) Press and HOLD the "set" button down untill the hours digits start to flash. 5) Now press the "set" button again six times. The time zone characters will flash. 6) Press the "adjust" button untill your time zone appears. 7) Press the "mode" button to return the clock to normal operation. 8) Press the "adjust" button to display the day-of-week.
Read More At : 86742 Digital Atomic Wall Clock...

After changing the batteries in my skyscan wall clock and transmitter, the time will not register, and the date is wrong. I've waited 24 hours for it to reset with sattelite, but nothing has happened.


Place the clock near a westerly window, if possible. It should only take a few minutes to reset. These clocks work using signals sent by terrestial radio waves, not satellites.
Read More At : 86709 Atomic Wall Clock...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || diydecoridea.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0963 seconds