Guide :Home : Home

What is normal pressure at pool sand filter when pump is running?

New house, old pool. Gauge at sand filter was not working and was replaced. What is normal? Showing about 12 psi. Approximate 18000-20000 gallon pool using a jacuzzi magnum 1HP pump. Also, where do I find a manual on the pump?

Research, Knowledge and Information :


Understanding Pressure Gauges | SwimmingPool.com


Understanding Pressure Gauges. Knowing how to read your pool filter pressure gauge and what to do if it’s not reading right can save you time and money.
Read More At : www.swimmingpool.com...

Normal Pump Pressure - Trouble Free Pool


I have a sand filter and my pressure is about ... is pretty normal. I do think the pool contractor who did the ... Filters, and Plumbing > Normal Pump Pressure.
Read More At : www.troublefreepool.com...

High Pressure Problem On A Swimming Pool Sand Filter


High Pressure Problem On A Swimming Pool Sand Filter. ... We got sediment in our pool from running our well dry ... water flow back to the pump. High pressure ...
Read More At : www.clean-pool-and-spa.com...

Pool Filter Pressure Problems


Pool Filter Pressure Problems. ... system operates at a different pressure. Your filter may be clean and normal at 9-10 ... a problem after the pool pump, ...
Read More At : blog.poolcenter.com...

Understanding the Pressure Gauge on your Pool Filter


Understanding the Pressure Gauge on your Pool ... pool filter and everything in your pool is running ... a sand filter is key to performing regular pool ...
Read More At : www.swimuniversity.com...

How to Reduce the Pressure in a Swimming Pool - SF Gate


How to Reduce the Pressure in a Swimming Pool. ... pool pump and filter. Open the pressure relief valve ... not return the pool to its normal water pressure, ...
Read More At : homeguides.sfgate.com...

Pool Info: Sand Pool Filters - Poolcenter


Pool Info: Sand Pool Filters. ... Open air bleeder assembly on top of sand filter, and turn pump on. Watch pressure gauge for ... (and the pump is running for ...
Read More At : www.poolcenter.com...

How to Reduce High Pressure in Your Pool System - INYOPools.com


How to Reduce High Pressure in Your Pool ... all my lines and no problems.I stated up my pool and my sand filter pressure is runing at ... with pump not running.
Read More At : www.inyopools.com...

Suggested Questions And Answer :


What is normal pressure at pool sand filter when pump is running?


This is normal pressure! As the filter becomes more dirty you will see the pressure get higher 15/20 it's time to backwash!
Read More At : Home...

Pressure at 15 psi after backwashing


No that is normal pressure, when the pressure rises more than 10 psi over that in a 24 hour time, you should backwash the filter. Hope this helps
Read More At : Home...

Pool pump won't shut off


1) timer is on over ride 2)timer faulty -replace timer 3)wiring done incorrectly -power to pump is still present when timer goes off
Read More At : Home...

I'm a tech working on a Nordic Hot Tub Single pump Impulse there is a flashing code of R60. Also when I reset the power the pump will run from 30-60 seconds and shut down. The water temp is 66 F. I'm figuring its on freeze mode. But the tub is within the owner's commerce not installed exterior. The tub is often in FLO, I've replaced the pressure switch and it worked for some time. Everytime the owner empties and refills the spa it goes into FLO, to which I suggested to to the owner to fill the tub through the filter basket to avoid air lock. Often the spa will run for several days without any trouble then all of a sudden just stop working properly. I'm wondering if the temp sensor is the problem or if its the keyboard. I've checked the element for cracks or discoloration and it looks good. I also checked the element for continuity and it appears to be good. But the R60 code is puzzling me, I haven't been able to find anything on it. The spa is being controlled by either a "U" or "J" class control box by Spabuilders. Thx


I am having the same problem did you find the answer?
Read More At : Jacuzzi...

I think I have an air block in my spa pool, this may have turned off a switch when I went to start it up for the first time. I forgot to release the pressure valve on the filter and now the pump will no longer start up


Check pump and bleed pump can be removed and checked not big job
Read More At : Home...

Low pressure from the undersink osmosis filtration system


A pump will help you
Read More At : Home...

The unit will not heat any water, press hot but goes straight to


Probley heater eliment ? if not megga dear unit buy new one probly cheaper as long as u fit ure self
Read More At : Home...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || diydecoridea.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0831 seconds