Guide :Home : Home

Electrical installation what size cable and rcd should i use to install a bikos whirlpool bath it has a 1hp 230V 800 W quite pump and a halogen light

Posted by tonyxx on Nov 18, 2008

Research, Knowledge and Information :


Electrical Installation guide | Switch | Power Inverter


Electrical Installation guide. ... It should he noted that a residual current device ... Maximum length of run for this circuit with the same cable size and type will ...
Read More At : www.scribd.com...

TraderTAG Victoria - Edition 26 - 2012 by TraderTAG Design ...


TraderTAG Victoria - The Weekly Buy ... internal light, rear stands, electrical certificate, spare wheel, ready to go, just plug in ... markets etc. Easy to use ...
Read More At : issuu.com...

TechieNation.Com » Solar Investigation : How many solar ...


199 Responses for "Solar Investigation : How many solar ... there is just a small solar installation with 4 panels 85 w and 2 ... but there should only be 1 light ...
Read More At : www.techienation.com...

Notes on the Troubleshooting and Repair of Small Household ...


... or by a ground water pump. The water has a certain ... on electrical contacts. One should also NOT use a ... any size though a typical night light might be ...
Read More At : www.repairfaq.org...

2009 Conely Pool | Swimming Pool | Pump


... 2009 Conely Pool & Spa. ... BATH PUMP 1HP W/SWITCH ... Compact in size and require a minimum installation space - light weight • Significant energy ...
Read More At : www.scribd.com...

TraderTAG Victoria - Edition 25 - 2012 by TraderTAG Design ...


TraderTAG Victoria - The Weekly Buy ... markets etc. Easy to use, install and program ... Spa Stylus Bath never used, c/w pump heat blower microjet controllers, ...
Read More At : issuu.com...

Garden & Outdoors - Page 100 | Shop online


Garden & Outdoors, Find it. Track it. Buy it. on ehomeware.co.uk, visit us and save money with our price tracker. Coffee makers, cookware, bakeware products with the ...
Read More At : ehomeware.co.uk...

TraderTAG Victoria - Edition 26 - 2012 - Documents


TraderTAG Victoria - Edition 26 - 2012 Mar 10, ... large cooling system, internal light, rear stands, electrical ... markets etc. easy to use, install and ...
Read More At : documents.mx...

Schneider Electrical Installation Guide-2010 | Electrical ...


Schneider electrical installation guide ... Locations containing a bath tub or shower basin Electrical ... the use of halogen gas allows a more concentrated light ...
Read More At : zh.scribd.com...

aquaforce 1000, 2500 & PDF - docplayer.net


A 10mA or 30mA Residual Current Device ... The pump cable (and extension cable) should be positioned and ... Bollard Light Installation and Operating ...
Read More At : docplayer.net...

Suggested Questions And Answer :


Electrical installation what size cable and rcd should i use to install a bikos whirlpool bath it has a 1hp 230V 800 W quite pump and a halogen light


From the specs that you are showing 800 watts @ 230 volts will pull under 3.5 amps. I would install a 20 amp 220 volt circuit with #12 wire. Just double check if the tub requires a 3 wire ckt (2 hots & ground) or a 4 wire ckt. ( 2 hots, neutral & ground) Make sure the ckt. is GFCI protected!
Read More At : Home...

Kohler bathtub spa does not work at all


If the air tube is still connected to the air button on the side of the tub and you are pushing it with no results then either the motor is no good, the air button is no good or the air switch in the box is no good.process of elimination, start with the pump. take the switch off the motor or out of the box and make sure you can get the motor to come on. If the motor comes on then move to the air switch and hook it back up and see if you can blow into the air switch with a new air button or a straw and see if the switch will activate the pump. if it does then you most likely have a bad air button ($12). If you cannot get it to activate the pump then the air switch is bad ($21).
Read More At : 1107-R-0 ProFlex Bath Tub with Flange and Right Hand Drain......

Fuel problem ???


Filter must always be changed when pump is. replaced.
Read More At : Yosemite Home D?©cor - Polished Cream and Brown Onyx Sink...

What is normal pressure at pool sand filter when pump is running?


This is normal pressure! As the filter becomes more dirty you will see the pressure get higher 15/20 it's time to backwash!
Read More At : Home...

We have a oasis whirlpool bath tub model s2283-6j3wht that stoped working, there is power to the plug in, but no lights will light or pump wont run


Possibly an internal fuse has blown..
Read More At : Home...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || diydecoridea.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0573 seconds