Guide :Home : Home

Installing an Aqualux (Desiree) whirlpool bathtub

I purchased a floor model of an Aqualux Whirlpool bathtub and of course it came without installation instructions. I've searched the internet but so far have been unable to locate instructions or the technical specifications. Any idea on where to find them?

Research, Knowledge and Information :

What does Desiree mean in history? -

Installing an Aqualux (Desiree) whirlpool bathtub Answers: 2; BECOME A GUIDE. Share your knowledge and help people by answering questions. Register Now. Unanswered ...
Read More At :

How Do You Clean Whirlpool Jets ?? - Houzz - GardenWeb

How Do You Clean Whirlpool Jets?? ... We just moved into a new home with a jacuzzi bathtub, ... so if you're installing a new tub, ...
Read More At :

Explore Shower Base, Shower Door, and more! - Pinterest

Features: -180° Pivoting door for easy access. -Can be installed on any 60" x 32" acrylic or tiled base (shower base sold separately). -Frameless design.
Read More At :

Suggested Questions And Answer :

Installing an Aqualux (Desiree) whirlpool bathtub

Call the manufacturer Asteria Bath Company at1-800-288-4002 and they can send it to your email address.
Read More At : Home...

I have an aqualux whirlpool tub w/ cracked jet housing

I have the same issue is there a way u can tell home it is done i live michigan
Read More At : Home...

Need to know how to access the motor on my whirlpool tub

Yes you should have an access panel to the pump somewhere. It sounds like you have already found it. You may want to get a qualified electrician involved. There are at least three sources of possible failure. The first and least expensive is that the motor tripped the ground fault interrupter and just needs to be reset. The second is that the switch has gone bad. The third and most expensive is that the pump is broken and needs to be replaced.
Read More At : Pearl AIGO True Bathtub with Back Massage - 103556-100...

Whirlpool Tub Access

Hi garyv47, I'm Harvey the Master Plumber. Your question is: Your daughter just purchased a new condo with an AquaLux whirlpool tub installed in the bathroom. The front side is removable for access to the mechanicals and is held in place on the lower side by velcro. When you pull the velcro loose the side begins to tilt up, but then stops as it hits the upper edge of the tub. You tried pulling down, but it appear to be held by something. You don't want to pull too hard and break something. Any ideas on how to remove it? It has been my expirience that the top of these access panals are 'tongue and grove' type construction and are not connected to anything. Usually disconnecting the bottom and pulling the bottom out works. If you are concerned about breakage then it migt be wise to consider the Repair Directory to find a reparman. Or you could talk to the condo maintenance guy. You'll find these guys are a wealth of info. Feel free contact me again!Please give me a rating here at before you sign offThank you,Harvey your Master Plumber
Read More At : Home...

Need to replace casing around one jet

Go to and look at the picures of jets.
Read More At : Home...

Can Jacuzzi Rapid Heat inline heater be installed upside down?

You do not want to install any heater upside down because if any debris gets inside the heater pressure switch while it is running it will NOT shut off once the pump shuts off.RodUS Parts Center888-521-6183
Read More At : RapidHeat In-Line Heater U395000 [ Bathtubs and Whirlpools,...

Installing a bathtub on concrete floor

Other than chopping out more concrete.elevating the tub is probably your only other solution. I would think 2" would be adequate. Hope this helps. Bob
Read More At : Crane Plumbing 2430W Whirlpool Bathtub, White...

How do I install a whirlpool bathtub? - Whirlpool 5"x36" White Bathroom Drop-in Bathtub Spa Jet

We have a kohler whirl pool bathtub and have no instructions for it. can. someone help us and tell us what to do.
Read More At : 5"x36" White Bathroom Drop-in Bathtub Spa Jet...

Only used my Royal whirlpool bathtub about three times

My jetted tub will not work, and it used to work just fine. Nothing happens when i push the button to turn it on. Could this be a switch problem? Also do not hear the motor doing anything when button is pushed. Dou you think I just need to get a new pump??
Read More At : Home...

Bathtub whirlpool leaks. problem is that the tub

Stop leak in a bottle absolutely does not work, look closely there should be some sort of access panel (maybe well hidden) to get under there.
Read More At : 5"x36" White Bathroom Drop-in Bathtub Spa Jet...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0457 seconds