Guide :Home : Home

Shower base We installed a one piece shower base, but later discovered there is some flex around the outside perimeter of it. Is there anyway to shim or reinforce this without starting over?

Posted by stubby22 on Nov 14, 2008

Research, Knowledge and Information :


Inspecting Tiled Showers and Shower Pans - ASHI Reporter


Inspecting Tiled Showers and Shower Pans ... there’s some minor grout ... between a good inspection of a tiled shower and a disastrous one is what we look ...
Read More At : www.ashireporter.org...

Get a Bathroom That Looks and Feels Amazing - Home Repair Tutor


You’ll be one step closer to getting a bathroom that looks and feels amazing…and we ... shower surround that can flex a bit. We ... over that. We have some ...
Read More At : www.homerepairtutor.com...

Tricks How To Build Shower Pan: How To Build A ... - Pinterest


There are still some finishing ... Our Tile Ready shower pans are one piece shower ... We over the best shower installation with bathroom tile flooring at an ...
Read More At : www.pinterest.com...

Common Laminate & Floating Floor Problems… With Corrections


Common Laminate & Floating Floor ... This is happening all over the room. Not just in one area. When we walk on the floors ... Is there a solution minis starting over?
Read More At : www.lumberliquidators.com...

Bowed Durock Wall Fix? [Archive] - Ceramic Tile Advice Forums ...


The base of the shower is masonry ... I guess I could put some tape around it to ... I ran one piece of kerdi from the outside of the curb up the curb and then ...
Read More At : www.johnbridge.com...

Long tile shower with linear drain [Archive] - Ceramic Tile ...


The rounded slope that varies all around the shower means that some ... The second piece was our best one, though there are ... Outside the shower area we ...
Read More At : www.johnbridge.com...

Explore Corner Shower Kits, Corner Showers, and more! - Pinterest


... If you just have the possibility in your RV get one of these awesome shower wall kits! Once in life there ... shower base. The Flex is ... one-piece shower ...
Read More At : www.pinterest.com...

Hardwood To Tile Transition - How To Make The Transition


I have suggested he use some extra wood we have and put in a piece to ... the kitchen without there being ... one. The tile was most likely installed over the ...
Read More At : www.homeconstructionimprovement.com...

ELIMINATING PROBLEMS WITH DRYWALL BUTTED SEAMS | This Is Drywall


32 thoughts on “ ELIMINATING PROBLEMS WITH DRYWALL BUTTED ... if you need to hang one piece on ... If not is there another solution without tearing out the ...
Read More At : www.thisisdrywall.com...

Suggested Questions And Answer :


Shower base We installed a one piece shower base, but later discovered there is some flex around the outside perimeter of it. Is there anyway to shim or reinforce this without starting over?


Sorry to say. the answer is no. since it is a one piece. the only way for you enforced the tub is from under neath, which is from the inside.
Read More At : Home...

Need to remove silicone from 4 part shower stall to repair & reinstall


I think you should contact to a professional who can remove this shower stall very easily without any risk. You can also have a look at shower enclosures for having such bathroom stuffs in affordable price.
Read More At : Home...

I have a Maax Tigress shower. This will be 3rd time I've taken shower door frame off base to recaulk. I have leaks where frame meets base. I don't think base is stiff enough, because I can feel it flex when I stand in shower. This is probaly breaking the seal of silicone. Anyways I've tried GE Silicone II, and Mono Silicone, and I used a very liberal amount... Now what?


If the GE Silicone was used first then this may be the cause. For some reason the GE formulation does not adhere very well to new plastic/acrylic, however it does very well on most other surfaces. The mono brand is better for plastics/acrylic. If all of the GE silicone was not removed before the mono was applied then the mono formulation would not stick very well to the GE silicone that was not entirely removed. Unfortunately there is no easy way to do this other than with a plastic scraper tool and lots of elbow grease. Rubbing alchohol can be used to soften the silicone slightly and will not damage the acrylic, aluminum or glass. If the mono was applied first then the flexing will be the problem. The only solution to a flexing problem is to remove the shower unit and reinstall the unit in either a morter or sand base to provide more support for the shower unit. If you use a morter base ensure there is a vapour barrier installed between the morter and the shower unit as the chemicals/minerals in the morter will degrade the shower base over time. The downside to morter is that it will not flex and may cause cracking over time if and when the house shifts. A sand base will shift with the house.
Read More At : Maax...

Shower stall in master bath of a 15 yr old home. the shower started having water problems after about 1 year, leaking water onto the drywall next to the stall. we have tried everything-recalking, sealing the grout, checking plumbing to see if it was leaking. about 5 years ago, we took the whole shower down to the studs and started over-we retiled, grouted, sealed, and calked. water problems again with wetness on the drywall. we pulled out the calk to recalk again, the shower has not been used for 3 days, and water is still seeping out between the tile and shower pan. who should we call to fix this problem?


Did you use plastic pipe? What about the shower head? Does it have a rubber o-ring in it? Pull the pipe out of the wall at the shower head and peek inside for the o-ring. If it is there, just snug up the pipe, do not over tighten. We were ready with crow bars in hand to destroy a brand new shower we just finished, because we thought we had w broken pipe, Then the owner says he torqued up the shower head as tight as he could and I read where it had to be just finger tight. One more place to check is the faucet itself, take off the trim ring and look in there for drips. It could be filling up the wall cavity and stay wet for days. I would take apart the drywall on the other side before busting up the tile again. Check it out.
Read More At : Kohler...

Moen single handled shower the hot water turns cooler then cold after a minute


Your whole house is likely plumbed wrong so that it is impossible to have equal pressures of both hot and cold at your shower. If you had your home plumbed with aquapex using a radiator for the hot water and a radiator for the cold water and have the radiators fed with a 1 inch line you can have close to perfect pressures.
Read More At : Moen...

I have a Sterling shower with Vikrell base. The base has discolored. Can anything be done to repair it?


Yes there is. You will have to go to a place that sells that brand and ask them how to get in contact with the people who repair them in your area.
Read More At : Home...

Bathroom stall shower


Or add a 1/2 coulping and a peice of brass nipple and lower it where you want
Read More At : Home...

Yellow Spots on Bathroom ceiling/walls after showers


You will have to paint over your new paint with a primer called BIN which will dry in about an hour. Then you can put your color coat on that. Problem solved.
Read More At : Home...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || diydecoridea.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0676 seconds