Guide :Home : 86742 Digital Atomic Wall Clock

Skyscan 87700 Digital Atomic ----outside temperature reading not working

Just recently the outside temperature reading have stopped coming in on the clock. I did all new batteries and sprayed it with a electronic spray but with no results

Research, Knowledge and Information :

Order Replacement Temperature Transmitters | SkyScan Atomic ...

Order Replacement Temperature Transmitters. ... SkyScan Blog. Why Can’t I Return a Clock to SkyScan that I Bought on Amazon? Why Don’t We Take Telephone Orders?
Read More At :

SkyScan Atomic Clocks | Customer Support & Service

The US Atomic Clock is the most accurate clock in the world and the official national timepiece. This clock is operated by the National Institute of Standards and ...
Read More At :

SkyScan Atomic Digital Clock with Indoor and ... -

Moved Permanently. The document has moved here.

SkyScan Atomic Clock with Temperature Sensor (88905)

Buy SkyScan Atomic Clock with Temperature ... The transmitter stopped working and a replacement was not ... We couldn't get an outside temperature reading for ...

SkyScan Indoor/Outdoor Temp w/Atomic Clock Product ... -

SkyScan Indoor/Outdoor Temp w/Atomic Clock product ... problem with the outside temperature display ... to get my remote temperature reading to work ...
Read More At :

3 Ways to Set SkyScan Atomic Clock - wikiHow

How to Set SkyScan Atomic Clock. ... Setting a SkyScan Digital Clock Setting a ... Transmitters display the current humidity and temperature indoors and outside that ...
Read More At :


Find best value and selection for your New SKYSCAN Atomic Clock TEMPERATURE ... SKYSCAN ATOMIC DIGITAL CLOCK ... Atomic Wall Clock with Indoor Temp Reading ...

skyscan temperature transmitter | eBay

skyscan temperature transmitter 0 ... Vintage SkyScan Atomic Wall Clock with Indoor Temp Reading, ... SKYSCAN ATOMIC DIGITAL CLOCK WITH INDOOR TEMPERATURE SENSOR ...

How do you set outside temperature on Sharp atomic clock ...

How do you set outside temperature on Sharp atomic ... How do you set skyscan Atomic ... the clock and wait for the outside temperature to set. DO NOT SET THE ...
Read More At :

Suggested Questions And Answer :

I have eight atomic clocks,none of them have the outside temperature working,all have new batteries???

If your outside temperature is not showing on your clock, that may mean that the clock and the transmitter have lost their connection. To reconnect them you must first take the batteries out of both of the units for 15 minutes. First put the batteries back into the transmitter, and then the clock. Let them sit side by side inside your home. When both the indoor and outdoor temperatures show on your clock with the same reading, or within two degrees of each other, then you may put your transmitter back outside. Remember to keep the transmitter out of the direct sun in a dry place. Also keep it away from metal, which can affect the readings.
Read More At : 86742 Digital Atomic Wall Clock...

Everything but the outside temperature is working. We took the batteries out of both units,waited 10 seconds and put in new batteries in the inside clock, and then waited 3 minutes before putting in the outside unit. That was several hours ago and still not reading.Thank you for your help.

I have found a link to Skyscan FAQ's and it has a little bit more time required to reset the system.I am not sure if it applies to all models but I could not find the manual for your particular model.It is a quick easy read and fix.I am not sure why but they recommend Duracell,but basically an alkaline battery is an alkaline battery.There is very little difference in how long an alkaline battery will last but lithium is different and lasts longer than alkaline but still,lithium is lithium and most will last very close in usage time no matter the brand(just for your info).The decision is obviously yours.If this doesn't work,please reply to this post and I will get an auto link.Good luck! Greg
Read More At : 86742 Digital Atomic Wall Clock...

Outside temperature not working on Atomic Clock (was working last night). Changed the batteries in both the outside transmitter and the clock tonight. Clock reset within minutes, but the outside temperature still not showing on the clock. Please advise.

Hello lucy... you most likely have some corrosion in the outdoor component. Remove the batteries from the outdoor component and clean the battery contacts with the eraser end of a common pencil. Reinstall the batteries and then give it up to 8 hours to start reporting accurately again. Joe Thanks for choosing Fixya!
Read More At : 86709 Atomic Wall Clock...

3M Precision Digital Atomic Wall / Desk Clock with Indoor & Outdoor Temperature and Alarm will not display outdoor temp, i have replaced batteries, outdoor sensor is transmitting, does not appear to "sync" with receiver

After replacing the transmitter batteries several times, I tried replacing the clock batteries. They must have been getting low. Once I put in new batteries in the clock it worked fine. Good Luck.
Read More At : 86742 Digital Atomic Wall Clock...

Skyscan digital wall clock just quit showing outside temperature

You probably need to 'pair' the outdoor sensor with the main base: look for a 'channel' button, as these units usually can get information from several sensors and differentiate them by a channel number.
Read More At : 86742 Digital Atomic Wall Clock...

I have an acurite atomic wall / weather clock but the outside temperature is reading blank. I changed the batteries in the transmitter but still no reading. Where can I purchase a new transmitter. The only numbers I can find on the clock read as follows: 6608a-750-77rx. Thank you for any help you can give me.

I had one of these a while back and it had a required sequence for putting in the batteries. When the signal dies and you have to replace the transmitter batteries and the clock batteries in a certain sequence. The transmitter batteries cannot just be replaced. You also had to remove the clock batteries, then put in the transmitter batteries, then replace the clock batteries.
Read More At : 86742 Digital Atomic Wall Clock...

Outside temperature won't work

Please check the following website for all the info and faq., If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:1. Make sure you have good batteries installed in the remote transmitter2. Remove the batteries from the main clock and keep them out until the clock display disappers.3. Re-install the batteries in the clock.4. Wait until the display returns and includes the outside temperature display as well.5. Set the clock again for current time/date etc. 6. Bingo. You are in business.
Read More At : 86709 Atomic Wall Clock...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0604 seconds