Guide :Home : Home

Mirror glued to wall

We have a 6'x1' mirror glued to our bathroom wall. I tried getting a large putty knife and running it behind the mirror, causing the top to crack. From what I understand, i need to duct tape the mirror and then get some wire behind it to "peel" it off. Any further suggestions before I do this? We also have a 3'x3' mirror in the same bathroom glued to the wall and we want to take this one down too; I just see it being way to difficult. Any suggestions for this? Yes, we plan on repainting it soon so keeping the wall nice is not a priority. The mirrors were glued to the wall when we bought

Research, Knowledge and Information :


Remove a Bathroom Mirror - Lowe's


Before remodeling a bathroom with a new vanity mirror, you have to get rid of the old one. Here's how to remove a glued-on mirror quickly and safely.
Read More At : www.lowes.com...

How to Glue a Mirror to a Wall | Home Guides | SF Gate


Frameless mirrors attach to a wall with mirror clips or special glue known as mirror mastic. Many designers prefer mastic instead of clips because the edges of the ...
Read More At : homeguides.sfgate.com...

2 Easy Ways to Remove a Wall Mirror (with Pictures)


How to Remove a Wall Mirror. Many bathrooms feature large mirrors that are simply glued directly to the wall without a frame. The benefit of these mirrors is that ...
Read More At : www.wikihow.com...

How to Glue a Mirror to a Wall | Hunker


While there are several ways to stick a mirror to a wall in your home, a more permanent method involves actually gluing the glass to the wall using a special adhesive.
Read More At : www.hunker.com...

Mirror, Mirror Glued to Wall, Now I'm Stuck, Whom Shall I Call?


Apr 12, 2006 · Q I have a bathroom mirror that has been glued to the wall. Why would anyone have done that? And is there any way to get it off without ruining the wall ...
Read More At : www.washingtonpost.com...

How to Safely Remove a Wall Mirror - DIY Network - YouTube


Oct 25, 2010 · Here's the safest way to remove a wall-mounted mirror in one piece. ... How to Safely Remove a Wall Mirror ... How to remove glued mirrors from a wall ...

How to Remove a Bathroom Mirror: 9 Steps (with Pictures ...


How to Remove a Bathroom Mirror. Mirrors are deceptively heavy. ... If your bathroom mirror is not attached to the wall with glue, your job will be a lot easier.
Read More At : www.wikihow.com...

How to Remove a Mirror From a Bathroom Wall That Was Glued


When removing a mirror from a bathroom wall, you're going to need a hand trowel and a hammer. Remove a mirror from a bathroom wall with help from a foreman for Lighty ...
Read More At : homeguides.sfgate.com...

How to remove mirror glued to the wall - Daily Herald


Q. I would like to remove the mirror in our bathroom that is glued to the wall. I do not want to destroy the wall and have read a few suggestions on the Internet. Do ...
Read More At : www.dailyherald.com...

Amazon.com: Glue Mirror To Wall


Brown Bare Autumn Tree Branches Wall Decal Sticker 6ft Tall by Stickerbrand - Easy to Apply and Removable - Made in the USA - No Glue Needed. Safer than wallpaper ...

Suggested Questions And Answer :


Mirror glued to wall


That's actually a pretty common method for professionally installing bathroom mirrors. As you mentioned, tape a star pattern on the mirror and then use a thin piece of piano type wire to slice through the adhesive. Keep the ends of the wire as close to the wall as possible while cutting so that you don't break the mirror. A local glass company can provide the best type of wire for the job as well as tips on the best way to get the job done - particularly if you imply that you'llbe buying your new miror from them. Be sure to wear leather palmed gloves and eye protection when doing this job!
Read More At : Home...

How to best use Stanley Mirror Mastic?


Make sure the wall where the mirror is going to be, is perfectly flat. if you are going to install the 4x6 ft mirror. you need minimum of 3/8" board, if not 1/2". yu use mastic the same way you use caulking. on the safety side, I recommend you install upper and lower railing. the mastic will hold the mirror, three glop on each side and enough in the body of the mirror. press on hard, but too hard you will break the mirror the mastic will take about a week to cure completely.
Read More At : Home...

Bathtub wall was cut short and is leaking to downstairs when we take showers


Fill the space with liquid foam filler made for water areas. this will seal and fill the space, keep it below the surface as it does expand and will go above the tubs line. let it dry the recommended time and cut off the excess with a razor blade. once that's done then you can caulk normally to hide the foam.
Read More At : Home...

The wall of my bathtub was cut too short and water leaks to downstairs how can i fix it


Fill the space with liquid foam filler made for water areas. this will seal and fill the space, keep it below the surface as it does expand and will go above the tubs line. let it dry the recomended time and cut off the excess with a razor blade. once thats done then you can caulk normally to hide the foam.
Read More At : Home...

Even though professionally installed, I cannot reposition the mirror any way other than resting the bottom of the mirror against the wall. Product is Delta Oval Tilting Mirror 138265 (Greenwich Collection)


Us too! We'll probably put a doorstop behind it. Don't know what else to try
Read More At : Home...

Clumps falling out of crevices


A bathroom remodeler.
Read More At : Home...

Are 6mm screws strong enough to hold mirror that weighs 7.92kg


Info on the screws seems incomplete. If they are 6mm diameter that should be more than adequate for strength. Since you're using plugs it's probably safe to assume that the walls are a minimum of 1/2" drywall, so the only thing to confirm is that the plugs are installed correctly in the walls, and that the screws are long enough to perform the two functions of anchoring the plugs to the drywall, and securing the mirror hangars to the plugs. Here's looking at ya!
Read More At : Home...

How do you install body jets for a shower


Hi mickgosney I'm Harvey the Master Plumber Your question is how to tighten up in the wall without putting a stud wall in for kyra body jets. Kyra sells about fifteen models and they are all designed to be installed in a wall of some type. The wall lends some very nessessary support to the valve body so that the whole thing dosen't move when the handle is adjusted. Wood stud, metal stud and concrete are typical structures. If you are trying to install on a free standing shower I recomend at least some kind of creative frame to support the valve. Feel free to contact me again. Please give me a rating here at fixya.com before you sign off.Thank you,Harvey your Master Plumber
Read More At : Home...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || diydecoridea.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0792 seconds